[server]
# Addresses the XRPC server listens on. When using as an env var, comma-separated.
#
# Can also be specified via environment variable `BOBBIN_BIND`.
#
# Default value: ["127.0.0.1:8090", "[::1]:8090"]
#binds = ["127.0.0.1:8090", "[::1]:8090"]

# The amount of time in seconds to allow in-flight requests to drain after sigterm
# before forcing the listener closed.
#
# Can also be specified via environment variable `BOBBIN_SHUTDOWN_GRACE_SECS`.
#
# Default value: 30
#shutdown_grace_secs = 30

# Address for the `/debug/mem` and `/debug/heap` introspection endpoints,
# for example `127.0.0.1:8091`. Empty disables them so the debug surface is
# never reachable on the public listener. Bind to loopback only.
#
# Can also be specified via environment variable `BOBBIN_DEBUG_BIND`.
#
# Default value: ""
#debug_bind = ""

# Reverse proxies in front of bobbin,
# each a bare IP address without a port or a CIDR block such as `173.245.48.0/20`.
# Bobbin will read the client address out of `x-forwarded-for`
# and forward that one address to the knot
# when a request arrives from a proxy on this list,
# so a knot that lists bobbin under its own `xrpc.trusted_proxies`
# can rate-limit per browser
# instead of pooling everyone bobbin serves into a single bucket.
# Bobbin will read the last 32 entries of the chain, at most.
# Leave empty when bobbin takes connections directly,
# since bobbin would otherwise believe a header any client can write.
# When using as an env var, comma-separated.
#
# Can also be specified via environment variable `BOBBIN_TRUSTED_PROXIES`.
#
# Default value: []
#trusted_proxies = []

[hydrant]
# Base URL of the hydrant instance - the cursor-replayable /stream lives
# under this. Use `ws://` or `wss://` - `http://` and `https://`
# are rewritten to the corresponding ws scheme at connection time!
#
# Can also be specified via environment variable `BOBBIN_HYDRANT_URL`.
#
# Default value: "http://127.0.0.1:13010"
#url = "http://127.0.0.1:13010"

# The cursor to request on first connect. Reconnects ignore this and resume
# strictly after the last cursor seen internally.
#
# Can also be specified via environment variable `BOBBIN_START_CURSOR`.
#
# Default value: 0
#start_cursor = 0

[ingest]
# Concurrent in-flight resolves during ingest. One slot per slingshot rtt.
# Default 16 sits at the measured throughput
# knee for cold replay against a healthy hydrant. The committer stays
# serial so that like, cursor and Spur allocation order are preserved.
#
# Can also be specified via environment variable `BOBBIN_INGEST_PARALLELISM`.
#
# Default value: 16
#parallelism = 16

[backpressure]
# Estimated peak transient anonymous bytes a single hydrating request holds:
# roughly the page of decoded records plus its serialized copy. Combined with
# the detected cgroup memory limit to size the in-flight cap on heavy
# endpoints. Has no effect when no cgroup memory limit is present, the heavy
# path stays unbounded exactly as before.
#
# Can also be specified via environment variable `BOBBIN_BACKPRESSURE_PER_REQUEST_ANON_BYTES`.
#
# Default value: 2097152
#per_request_anon_bytes = 2097152

# How often the adaptive watcher samples memory.current/memory.max and
# adjusts the in-flight cap. Ignored when no cgroup memory limit is present.
#
# Can also be specified via environment variable `BOBBIN_BACKPRESSURE_ADJUST_INTERVAL_MS`.
#
# Default value: 500
#adjust_interval_ms = 500

# memory.current/memory.max ratio below which the watcher additively raises
# the in-flight cap back toward its ceiling. Sits below the memory.high
# throttle band so the kernel, not this loop, handles mild pressure.
#
# Can also be specified via environment variable `BOBBIN_BACKPRESSURE_RELIEVE_BELOW_RATIO`.
#
# Default value: 0.85
#relieve_below_ratio = 0.85

# memory.current/memory.max ratio above which the watcher multiplicatively
# cuts the in-flight cap and purges jemalloc arenas. Set above the memory.high
# watermark so this loop acts as the anti-OOM backstop, not a duplicate throttle.
#
# Can also be specified via environment variable `BOBBIN_BACKPRESSURE_TIGHTEN_ABOVE_RATIO`.
#
# Default value: 0.92
#tighten_above_ratio = 0.92

# Bytes held back for the edge index, state indexes, and other derived
# state that grows after startup. Folded into the heavy-request reserve so
# the static in-flight cap leaves the index room to fill. Has no effect when
# no cgroup memory limit is present.
#
# Can also be specified via environment variable `BOBBIN_BACKPRESSURE_RESERVED_INDEX_BYTES`.
#
# Default value: 67108864
#reserved_index_bytes = 67108864

[slingshot]
# Base URL of a slingshot instance. Used for record bodies and identity.
#
# Can also be specified via environment variable `BOBBIN_SLINGSHOT_URL`.
#
# Default value: "http://127.0.0.1:13011"
#url = "http://127.0.0.1:13011"

[record_cache]
# Bound of bytes on the in-process record LRU. Records evict on a weighted
# LRU policy keyed on URI plus payload length.
#
# Can also be specified via environment variable `BOBBIN_RECORD_LRU_BYTES`.
#
# Default value: 67108864
#lru_bytes = 67108864

[search]
# The heap size in bytes for the in-mem tantivy writer. Larger values
# trade RAM for fewer segment merges - the index itself lives in
# `RamDirectory` and is rebuilt from hydrant replay on every restart.
#
# Can also be specified via environment variable `BOBBIN_SEARCH_HEAP_BYTES`.
#
# Default value: 50000000
#heap_bytes = 50000000

[knot]
# Whether to allow the knot proxy to dial private/loopback addresses. Off in
# production - on for local testing against a knotserver on localhost.
#
# Can also be specified via environment variable `BOBBIN_KNOT_ALLOW_PRIVATE`.
#
# Default value: false
#allow_private = false

# Require https on knot hosts. Disable only when proxying to a local
# knot for development.
#
# Can also be specified via environment variable `BOBBIN_KNOT_REQUIRE_HTTPS`.
#
# Default value: true
#require_https = true

[log]
# Log emitter format. `text` produces human-readable output for local
# development. `json` emits one structured object per line for log
# shippers in production.
#
# Can also be specified via environment variable `BOBBIN_LOG_FORMAT`.
#
# Default value: "text"
#format = "text"

# `tracing-subscriber` env-filter directive. Defaults to `info` across
# every span - override with `BOBBIN_LOG=bobbin_xrpc=debug,info` etc.
#
# Can also be specified via environment variable `BOBBIN_LOG`.
#
# Default value: "info"
#filter = "info"